Learn about the different types of approved driveways, and how to get a permit to build a driveway on a maintained county right-of-way connecting to your commercial property.
Technical Standards
Travis County follows the City of Austin Type II Driveway Standards, or applicants can submit a seal site specific design.
- Driveways shall conform to the City of Austin TCM requirements for commercial driveways.
- Driveways cannot be closer than 60% of the parcel frontage or 50’, whichever is closer, to an intersecting right-of-way.
- Only 2 driveway approaches are allowed per street per property, and they must have at least a distance of 35’ inside edge to inside edge for curb and gutter streets or 100’ center to center for all other types.
- Driveway approaches must be paved with a hard surface, with concrete or asphalt.
- The angle of approach shall be approximately 90 degrees.
- Driveways shall be 12’ - 25’ wide at the right-of-way line, not including the radius.
- Ditch line grading and installation of driveways must ensure positive drainage for the entire length of property.
- The grade on all driveway approaches shall not exceed 15%, unless otherwise approved by Travis County.
- The line-of-sight 35 MPH roadway is 250’.
- There is a 2% max slope at sidewalk crossing
Driveway Approaches for Rural Roads
Straight Tie-In
Used when there is no roadside ditch section.
Dip-Style
Used when the roadside ditch is less than 12” deep.
Culvert Style
Used when the roadside ditch is more than 12” deep.
Key standards:
- Corrugated metal pipe is the only culvert pipe material permitted for use in the right-of-way.
- Culvert pipe must be at least 18” diameter, or a 15” high x 21” wide oval pipe (Design 2), placed at the proper grade to ensure positive roadside drainage.
- If this size or larger culvert cannot be placed per regulations, then a dip style driveway must be constructed.
- Culvert style driveways must include concrete safety end treatments to protect the culvert pipe and to ensure traffic safety.
NOTE: Non-residential driveway permits are traditionally issued concurrently with a non-residential development permit.
Driveway Approaches on Curb-and-Gutter Roads
Key standards:
- The grade of driveway may not exceed 2% where the sidewalk crosses the driveway.
- If a curb inlet is present there must be 10’ between the inlet opening and the edge of the driveway curb return.
Application Process
Verify Your Address
Driveways connecting to a maintained Travis County road require a Travis County Driveway Permit.
Driveways connecting to a state road require a TxDOT permit. Information on this page does not apply to those roads.
Travis County does not issue permits for driveways connecting to unmaintained/unaccepted roads.
To verify what city and county your property is located in, use the Jurisdiction Web Map.
Gather Required Information
The following information is needed to complete your application:
- Address
- Legal description of the property from Travis Central Appraisal District (TCAD)
- Lot # (if applicable)
- Block (if applicable)
- Phase and section (if applicable)
- Property ID (PID)
- Classify the driveway usage as residential or non-residential
- Classify the driveway approach as culvert style, dip-style, or curb and gutter style
- Provide the number of driveways and their approximate width at the property/right-of-way line
- Proposed construction start date
- Estimated date of construction
Unsure about required information or documents?
Our new tool Camino can help. Answer a few questions to get information that will assist with your application.
This version of Camino is a beta release and is intended as a supplemental tool to learn about likely requirements for your project. We have tried to build the tool to accurately capture the required steps, information, and documentation depending on the unique nature of your project, but it is NOT a substitute for Travis County Code or any other laws and regulations.
Collect Required Documents
Please collect all documents listed below:
- Non-Residential Checklist
- Site Plan sealed by a Texas Licensed Engineer that includes:
- Property boundaries
- Existing/proposed structures, including
- Mailboxes
- Guardrails
- Drainage inlets
- Etc.
- Proposed driveway location with distance from lot corners and between the edge of pavement and property lines
- Access/roadway easement, if driveway requires access from a property not owned by the applicant
- Applicant accepts responsibility/liability for damages to any/all properties associated with the installation.
- Platted Easements (if applicable)
- Environmental Resource Inventory (ERI)
- Required if developing an acre or more or part of a common plan of development (COPD)
NOTE: Non-residential driveway permits are traditionally issued concurrently with a non-residential development permit.
Create an Account
Travis County uses a permitting website to process development permits.
Once you complete all previous steps, please proceed to create a permitting account.
Apply for Your Permit
Once your account is created and phone number verified, you can move on to filing your paperwork.
Please have all the requirements in previous steps handy.
Start your online application.
Follow the instructions and steps provided within the platform.
In the “Select an Application Type” step, select “Development (Non-Residential)”.
Check the Status of Your Application
As we review your application, you can track the progress in the permitting website.
All communication associated with your permit application will be conducted within the same website. Please monitor your email and queue for status updates or comments associated with your application.
Respond to Our Comments (if applicable)
If the County has provided comments on your application, action is required by you to address the comments. The review process will be paused until you have responded sufficiently to each comment.
Receive the Permit
Once your application is approved, you will receive an e-mail notification.
Post the permit somewhere visible from the public right of way (ROW) on your work site before you begin your project.
Schedule Inspections
The driveway pre-pour inspection must be requested in MyGovernmentOnline.
Physical identification of property must be made within 48 hours after Driveway Permit Application submitted such as street marking or address board, which is preferred so it can double as a place to post permits and notices.
NOTE: The posted driveway permit after issuance must be readily visible to meet permit requirements.
- Driveway Approaches for Rural Roads
- A field assessment will be done upon permit application to ensure the design meets the roadside conditions.
- After permit approval, a pre-pour inspection is required to ensure construction will meet standards for final completion.
- Failure to contact Travis County TNR for a required pre-pour inspection, or failure to construct the driveway approach to the approved County permit and standards may result in a notice to remove and replace.
- Inspections are required for driveway approaches for Curb-and-Gutter Roads
- Framing
- Pre-pour
- Final
Areas of Consideration
- Ensure the property’s address is posted and visible from the street.
Related Permits
Projects associated with commercial properties, multi-family residence, or manufactured home parks.
Find information about permits for construction and remodeling projects outside corporate city limits in Travis County, such as:
- Subdivision Applications
- Driveways
- On-Site Sewage Facilities
- Demolition & Clearing
- More…
On-Site Sewage Facility (Septic System)
Learn how to get a permit to install a septic system on a commercial property.
Commercial Site Plan
Learn how to get a permit for the development of commercial non-dwelling projects, such as offices, medical centers, hotels, malls, large-scale utility projects, and more.
References & Code
Travis County Code:
- Chapter 464, Floodplain Management
- Chapter 480, Residential Construction Standards
- Chapter 482, Development Regulations